How to Make Wood Storage Shelves
5 Materials
$350
4 Hours
Medium
My garage had very little storage and as a result, organizing it was very difficult. I researched how to maximize the storage space in a garage and decided to put in wood storage shelves that custom fit storage bins I had.
In my research, I found many use ceiling storage. I was not wanting to do a garage storage system along the ceiling because I was afraid that putting up and getting down heavy items would be too difficult. So, with help, we built shelves in my garage to fit 50 of these 27 galloon storage bins/totes. They have been so useful! The storage shelves only take up the perimeter of the garage and the bins fit great on them.
To help with ease of getting items I need out of storage, I put the lighter totes on the top shelves (yarn, light decorations, etc.), the heavier ones lower to the ground (stationary supplies, tools, extra dishes, etc.) and the middle weight ones (Seasonal decor and clothing, extra bedding, etc.) in the middle. This storage system with these spacious bins, has made my life so much easier. My house is much less cluttered, finding things is very easy as I labeled everything using vinyl and my Cricut, and I’m able to park easily in my garage. It’s a great solution for much needed easy-access storage space.
When I bid this out, a local guy was charging $350 for an 8 foot unit installed. My friend did his entire garage (3- 8 foot units) for a few hundred ($800 savings). My friend wrote the following instructions for his wood storage shelving unit. I made mine taller (8″ ft tall and built in four shelves). The instructions are able to be tweaked a bit. So you can take these instructions and work with them a little to fit the size of your garage (height and width) and storage needs.
Cut List:
- Cut both sheets of plywood in half, length wise, giving you four sheets that are 2’ x 8’. One sheet will be scrap or can be used for a second set of shelves. Home depot can cut these with their panel saw for free or you can do it yourself with a table or skil saw.
- Cut six of the 2 x 4 down to 6’ long.
- Cut the six scraps (24”) from the previous step down to 21”.
Assembly
- Using a hammer create three rectangular frames for the shelf layers. The frames consist of two 8’ 2x4s and two 21” 2x4s. They will be attached in a vertical orientation with the short boards inside. Nail through the side of the 8’ boards into the end of the 21” boards.
- Attach the three sheets of plywood to the top face of the frame using the drywall screws. Line up one short end of the frame with one short end of the plywood first. Use leverage to line up the remaining edges so that the frame is square. Screws should be placed a minimum of 12” apart.
- Lay the shelves on their side as you plan to have them. Make a mark on the face of the long board in the shelving frame 46.25” from the end (this locates where the middle leg will go).
- Mark all 6 legs where the shelf frames will be located. Starting from the top of the leg, put a mark at increments that match the distance from level to level. This distance should be the height of the objects being placed on the shelf plus at least 4.5” (3.5” for 2×4, 0.5” for plywood and 0.5” for extra space). Each shelf can be at different levels based on your needs.
- Attach the front three legs to the shelf frames using the 3” wood screws. Each connection point should have 2 screws through the leg into the frame. Attach the legs starting at the top, working down and ensuring that the legs are square with the shelves.
- Flip the assembly over and attach the three remaining legs to the back side.
- Stand up the whole assembly, put it in place and attach it to the wall with wood screws, making sure to screw into the garage studs.
- Note my friend used 2×4’s in his garage. I tried using 1×1’s for the shelves in mine (seen in photo below). They are not as sturdy as the shelves made with 2×4’s. If I were to do it again, I would use 2×4’s and follow the instructions outlined in this post.
Want more details about this and other DIY projects? Check out my blog post!
Comments
Join the conversation
2 of 13 comments
-
I created 60 feet of shelving space in my garage using wood and shelf brackets from Lowe's. Google it or check out Lowe's website or ask at hardware store
-
T6
Frequently asked questions
Have a question about this project?
I don't understand what you have used the 2x6's that you've cut for. Your instructions call for 2x8's and 21" legs, but nowhere do I see where the other pieces go.